topblog Ivoire blogs

29/04/2019

How to Configure WiFi Connection for Original JLR DoIP VCI

Original Jaguar Land Rover diagnostic tool JLR DoIP VCI supports both USB and WiFi connection. Here’s the guide to configure the LAN setting.

Procedure:

Connect JLR DoIP VCI W-F interface with vehicle

Connect the other end of VCI with laptop via USB cable

jlr-doip-vci-sdd-1

Open VCI Manager (JLR), press Connect

jlr-doip-vci-sdd-2

Choose Network Setup tab->Wired Etherent

jlr-doip-vci-sdd-3
Tick Enable Wired Etherent Interface

jlr-doip-vci-sdd-4

Press Apply button and Yes

jlr-doip-vci-sdd-5

Then disconnect USB connection
Close VCI Manager
Open VCI Manager again
Press Connect
Go to Network Setup->Wired Etherent
Press Set Factory Default

jlr-doip-vci-sdd-6

Press OK if system prompts you are about to reset the VCI communication settings to a factory default state.

jlr-doip-vci-sdd-7

Enable network connection
Press Set Factory Default again

jlr-doip-vci-sdd-8

In Wireless (802.11), choose Obtain an IP address automatically, then press Access Point

jlr-doip-vci-sdd-9
Choose Wireless resource which is the same as the your network
Press Configure

jlr-doip-vci-sdd-10
Enter wireless security password (encryption key)

Press Next

jlr-doip-vci-sdd-11

JLR VCI is configured to connect to your network
Disconnect and then Connect VCI

jlr-doip-vci-sdd-12

It shows WiFi connection is done
Open JLR SDD software on desktop

jlr-doip-vci-sdd-13

Press Connect

jlr-doip-vci-sdd-14

Now you can run SDD software for diagnosis

jlr-doip-vci-sdd-15 jlr-doip-vci-sdd-16 jlr-doip-vci-sdd-17 jlr-doip-vci-sdd-18

18/04/2019

Autel IM608 IM600 “Function available on a pay-per-use basis ” Solution

Question:

Just found this in  advance mode after new update. When try to program VW 4th immobilizer all keys lost, Auro otosys im600 Auto Key Programmer gives error message “This function is available on a pay-per-use basis.  Continue or not?” How to obtain token for otosys ?

autel-im608-pay-to-use-function

Obd2tool.com Solution:

You need to pay 10USD for each car to do following function with Auro OtoSys IM600 or Autel MaxiIM IM608:

1. VW immo 4 instrument: key learning and all key lost by OBD;

2. IMMO 4+MQB Key: key learning and all key lost by OBD ;

3. MQB instrument: key learning by OBD for VW and Audi JCI type and few VDD instrument (like virtual cockpit instrument)  MQB system can only add key, no all keys lost.

14/04/2019

SEC-E9 key cutting machine feedback Excellent

SEC-E9 Key Cutting Machine feedback what can work and how to do, you are advised to own SEC-E9 instead of Xhorse Dophin / Xhorse Mini plus (since they have no stock yet). Besides, SEC-E9 has wide coverage like Car keys, motorcycles keys, truck keys, household keys, punch keys, tubular keys, single-sided standard keys,Tibbe keys and LDV keys, cylinder and laser keys(detail models, you can check SEC-E9 Key Cutting Machine Support Key List)

Here we go for SEC-E9 reviews:

Well thank goodness for the wonderful support I got with My sec e9 key cutting machine… This Machine is my company’s lifeblood I just started automotive about a year ago and could not afford much I sold my car by this machine and it has paid off from day one I was able start cutting high security key blanks any key really it always cut them perfectly absolutely perfectly. 1 day I woke up and it was cutting wrong I contacted my representative at the seche 9 company Leslie she got an engineer and several other people together for a conference call I showed him the problems I was having they came up with a solution and soon after my machine was up and running again it cuts perfectly every time I love this machine.

SEC-E9-key-cutting-machine-feedback-1 SEC-E9-key-cutting-machine-feedback-2

Excellent:

SEC-E9-key-cutting-machine-feedback-4
SEC-E9-key-cutting-machine-feedback-5

Kia sportage, COPYLLAVES:

SEC-E9-key-cutting-machine-feedback-6 SEC-E9-key-cutting-machine-feedback-7 SEC-E9-key-cutting-machine-feedback-8

Dimple key by SEC-e9…

SEC-E9-key-cutting-machine-feedback-8

How to cut this type of key?

SEC-E9-key-cutting-machine-feedback-9

You buy the key blank like that, you can’t cut it down on any machine. It’s dependant on the code series of the vehicle, 40k and 80k.

COLT-6pins all key lost..

SEC-E9-key-cutting-machine-feedback-11

SEC-E9-key-cutting-machine-feedback-12

SEC-E9-key-cutting-machine-feedback-13
Solving Fallas, with sec e9:

SEC-E9-key-cutting-machine-feedback-14

Question: SEC-E9 Pro how to calibrate Honda key?

You need to use two decoders to calibrate then you will see a massive difference mate

Question: why when I decode a key the numbers are red and blue . Do the colors mean anything?

Answer: This is called rounding. The blue number should be the number with a decimal point. The red color is an integer. If your original key is very worn, you can leave it off, so that the cut key is the same as the original key. If the lock is new and not worn, you can turn it on, so that the key that was cut out is what the original key was worn before. I mean there is a round-off button. when you deocder key. In another word, if it’s off , it will copy the key just as the customers key is . If it’s on it will round off to the correct factory depths .

Thanks to all users of Automotive key Programmer SEC-E9 key cutting machine’s feedback.